Used with 1-1475 Cross & Bearing.

Used with 1-1475 Cross & Bearing.

Used with 1-1475 Cross & Bearing.

2-1/2" Face, 1/4" NPT Bottom Stem (Glycerin Filled)

2-1/2" Face, 1/4" NPT Center Stem (Glycerin Filled)

Low Pressure Lock-On Hose. Available in black, blue, green, red, yellow, and gray.

High Pressure Hydraulic Hose.

High-pressure hose with abrasion-resistant MegaTuff® Cover.

High Pressure Hydraulic Hose.

High Pressure Hose with abrasion resistant MegaTuff® cover.

High-pressure hose with XtraTuff™ Cover.  XtraTuff™ hose lasts up to 25 times longer than standard hose during hose during hose-tohose and hose-to-metal abrasion tests per ISO 6945.

High Pressure Hydraulic Hose.

High-pressure hose with abrasion resistant MegaTuff® cover.  MegaTuff® hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO 6945.

High-pressure hose.  XtraTuff™ hose lasts up to 25 times longer than standard hose during hose-to hose and hose-to-metal abrasion tests per ISO 6945.

70 Durometer seals.  Kit includes 385 pieces.

Self-Colored

Best value for precise control of air and hydraulic fluids where a calibrated knob is required.

The Model DS 2-Position Double Selector Valve directs the flow of hydraulic oil to two separate circuits. This permits operation of two double-acting cylinders with one four-way control valve or four single-acting cylinders with two three-way control valves. The hydraulic circuit which is to be operated should be selected before pressure is applied. Valve is of the open crossover type. As spool is moved and one set of outlet ports start to close, the other set of outlet ports start to open.

The Prince DS Valve is a manual 6-way, 2 position double selector valve. This valve will divert the flow going to two separate hydraulic circuits. For example, two double acting cylinders or two reversible hydraulic motors can be operated by one four-way valve. When the double selector spool is pushed in, the top ports are connected to the right ports. When the selector spool is pulled out, the top ports are connected to the left ports. An optional series/parallel spools is also available. This spool will run two reversible hydraulic motors in series when the spool is out and in parallel when the spool is pushed in.

LO Lock Valves are designed to lock a cylinder, or part of a circuit, without leakage while a control valve is in a neutral position. Lock Valves function as check valves, allowing flow to a cylinder and blocking reverse flow until pilot pressure is applied to "unlock" the circuit. These valves may be used to prevent movement of a load while the pressure source is inactive.

SAE 1/4" blade terminals standard.

The Model PD, Proportional-Type, Pressure-Compensated Flow Divider offers an efficient means of proportionally dividing a single flow of hydraulic oil. The flow ratio from the outlet ports remains constant despite load differences between the ports. Outlet flow ratios are preset at the factory and a range of ratios from 50/50 to 90/10 are available. Flow through the Model PD Divider cannot be reversed. It is a flow divider only - not a flow combiner. A Model PDC with a combiner feature is offered by substituting a combiner spool assembly for a standard spool. This feature not only divides flow, but flow may be combined in reverse direction and synchronized in both directions. It is only available with a 50/50 flow dividing ratio. Neither model, however, should be constructed as a flow regulator. If other ratios are required with the combiner feature, contact us.

The RD-400 is a constant volume priority divider. It can be used in applications where two circuits are to be supplied by a single pump such as power steering sytems. In operation the flow of oil supplied to the inlet is divided into two flows, the priority flow and the excess flow. The priority flow will remain nearly constant with variations in pressure on either the priority or excess flow port and will also remain nearly constant with variations in the inlet flow. The RD-400R provides the same function as described above with the addition of a built-in pressure relief for the priority port only. This relief is factory set at 1500 psi.